RESET THE RIG.

Off road rigs take more abuse than any vehicle you'd actually consider clean. Mud, dust, sun fade, whatever the trail throws at it. This kit resets the whole thing in one pass. Every cleaner, protectant, conditioner, and brush you need, in one box.

• The full reset: Wash, clean wheels and tires, restore the undercarriage, dress the rubber, and lock in ceramic protection. End to end, no gaps.
• Tough on grime, safe on surfaces: Hole Shot, Solution, and Wise Guy break down heavy trail grime without damaging paint, trim, plastics, or wheels. Aggressive where it matters, safe everywhere else.
• Full ceramic protection: Clutch protects trim, powder coat, wheels, and aftermarket components. Punch-It seals the paint. Both hold up run after run.
• Every surface, the right brush: Six brushes cover tires, wheels, fender wells, undercarriage, tight wash spots, and tire dressing application.

Kit includes:

• (1) Hole Shot Prewash, 16 oz.
• (1) Hot Shot Soap, 16 oz.
• (1) Wise Guy, 16 oz. w/ Spray Bottle
• (1) Decked Out, 16 oz. w/ Spray Bottle
• (1) Punch-It Ceramic Detailer, 16 oz.
• (1) Solution Ready to Use, 32 oz.
• (1) Classy Chassis, 16 oz.
• (1) Clutch, 16 oz.
• (1) Flat Out Wash Pads 4-Pack
• (1) The Palm Pro
• (1) The Workhorse
• (1) The Bristle Boss
• (1) The Leveler
• (1) The Tire Tamer XL
• (1) The Reacher

How to Use

Step 1: Wheels, Tires, and Wheel Wells

1. Pre rinse the wheels and tires.
2. Spray Wise Guy on the wheels and tires.
3. Scrub the tires with The Tire Tamer XL, the lug nuts and intricate areas with The Workhorse, and the wheel faces with The Palm Pro.
4. Spray Solution on the wheel wells and shocks.
5. Agitate the wheel wells with The Reacher.
6. Repeat on each corner, then rinse.

Step 2: Prewash with Hole Shot

1. Fill your Foam Thrower with 2 parts water to 1 part Hole Shot Prewash.
2. Foam the entire vehicle and the undercarriage.
3. Use The Reacher to scrub the undercarriage (outside of the fender wells you already cleaned in Step 1).
4. Rinse the Hole Shot off the entire vehicle.

Step 3: Wash

1. Fill The Foam Thrower with 2 to 4 oz of Hot Shot and top off with water.
2. Foam the vehicle.
3. Scrub the paint with the Flat Out Wash Pads.
4. Use The Bristle Boss to scrub intricate areas like the grill, badges, plastics, and aftermarket components.
5. Rinse and dry the vehicle.

Step 4: Dress and Protect (the sauce step)

1. Spray Classy Chassis on the undercarriage, fender wells, shocks, frame, and rear differential.
2. Dilute Decked Out to taste (2 parts water to 1 part product for satin, 1 part water to 1 part product for high gloss), then spray on the tires.
3. Lightly spray Clutch on plastics, powder coated parts, wheels, aftermarket components, and the bed / bed liner / Line-X.
4. Let everything soak for 15 to 30 minutes.

Step 5: Level

1. Use The Leveler to level Decked Out on the tires.
2. Use a black applicator pad or a soft paintbrush to level Classy Chassis.
3. Use a microfiber towel or applicator pad to level Clutch.

Step 6: Finish with Punch-It

1. Spray Punch-It directly onto a clean microfiber towel.
2. Wipe a panel.
3. Flip the towel to a dry side.
4. Level out any remaining residue.

Punch-It removes any overspray from your dressings, leaves a light ceramic layer on the clear coat, and finishes the paint with slickness and gloss.

Detailer Tips

• Let the prewash do the heavy lifting. Give Hole Shot time to pull the grime off before you go into the contact wash with Hot Shot. The less dirt sitting on the paint when your pads touch it, the less chance of swirling.
• Work in shade if you're on hard water. Direct sun plus hard water leaves spots on the paint, working in shade gives you time to rinse before it sets.
• The longer the soak, the easier the level. 15 minutes is the minimum on Step 4, but the longer you let Classy Chassis, Decked Out, and Clutch soak in, the easier everything wipes down clean.
• Use the right towel and brush for the job. Dedicated tools for each zone keeps grit out of the wrong places.
• Dial in Decked Out before you spray. 2 to 1 water to product gives a satin finish, 1 to 1 gives high gloss.